Crankshaft conversion

Cornwall Austin Seven Club creating interest in Austin Sevens

Last updated:
28 February 2010

012345678901234

Crankshaft Conversion 1½" (pressurised)

I have fitted a 1½" pressurised crankshaft in my Austin Seven. The conversion, I believe is very similar to the one that Austin would have fitted to your new Nippy or early Speedy, at extra cost. (Ulsters had an pressurized 1⁵/₁₆" crankshaft).

I hope this will be a useful guide if anybody else wishes to carry out a similar conversion in the future.

I would recommend that you have suitable good original parts to work with as you do not wish these bits to let you down. Any special engine modifications that I have not listed amongst my parts I will leave to you to source but for example you may wish to consider a high lift camshaft, large inlet valves, double springs, high compression head, change of carburettor or over bored block, just to name a few bits.

As you will see this is not a five minute job and you will need access to some machining, but the end result is very satisfying and I now run with a 50~70 psi oil pressure on the big end bearings, Combine this with the larger crankshaft journals makes the bottom end very strong and quite indestructible.

There are a few questions that I have been asked, and may be helpful;

Q1. What did it cost?
I estimate that the parts costs alone has been the wrong side of £1750.00, if you require to have block bored and a host of special bits then it’s just going to be more.

Q2. Was it worth it?
No! but for me it’s a yes (if that makes sense!)

Q3. Why did I do it?
I have always wanted a pressurized engine so for me this justifies it. The 1½" crankshafts are virtually indestructible and this is a big attraction for me. This now gives a engine capability of 6000 RPM (normal engines do not like much above 4500 rpm) not that I am planning going to these limits. One other major point to consider for me was I have had and known several incidents when the little end bolts have failed in these little engines with catastrophic results and I feel this is a very weak point. The Phoenix , Renault or original Nippy con-rods do not use these bolt, these having a fully floating gudgeon pin in the piston like most modern engines.

Q4. When should it this engine be considered?
I would strongly recommend that this type of engine is fitted, if you plan to push your engine hard (the racing clan would not contemplate using anything else) as the damage a broken crankshaft can cause at high speed is not worth thinking about.

Q5. Advice from what sources ?
Keith Rawson, John Barlow and Tim Myall, David Dye have been very helpful in my quest to build this engine.

Q6. What would you do different ?
Well I am still waiting for the new timing cover to be finished to accept a starting handle. other than that not a lot. If you wish to go down this route feel free to contact me.

Parts required: 1 x Phoenix Crankshaft; 4 x Phoenix Con-rods; 1 x Phoenix Nose piece; 1 x Set of shell bearings; 1 x Front timing cover; 1 x Set of front and rear bearings; 1 x Set Camshaft rollers; 1 x High pressure Oil pump; 1 x Relief valve; 1x Oils filter+ housing; 1 x Set of oil pipes and fittings; 1 x Complete gasket set;
1 x Rear seal cover; 1 x Set of tab washers; 1 x Set + 1 extra block to crankcase studs; 1 x Aluminium deep sump; 1 x Relief valve spring and ball; 1 x Small high pressure oil gauge; 1 x Set of new pistons [optional] or a set floating Gudgeon pins;
1 x Set of steel timing Gears [optional]

Parts to be modified:

Crankcase

1]. Oil jets remove and blanked, I copied the original jets but without the holes in the middle, I locktited them in for good measure.

2]. Camshaft location bolt removed and drilled to accept a ⁵/₁₆" diameter hole.

Camshaft

1] Front bronze bush oil hole reduced to ³/₃₂" size (using a 6 mm brass bolt as a plug) External ‘O' rings were fitted to outside of the bush to reduce oil loss. Modification to the bolt location to accept the additional block stud.

2] Rear bronze bush oil turned through 180 degrees and re-drilled with ³/₃₂" and a new chamfer added.

Small parts:

New oil pump housing machined to suit sump/housing.

New timing cover made to fit housing and chassis.

Flywheel assembly, con-rods and pistons balanced.

Sump also required some machining to suit new oil pump.

This article, written by Mike Davies, originally appeared in CA7C Seven Focus in Mar 2006 pp16-17.

Hit Counter

Last updated: 28 February 2010

012345678901234

Crankshaft Conversion 1½" (pressurised)

Last updated:
28 February 2010